Oct
28
Filed Under (LG Phone Problem and Solution) by lg-phones on 28-10-2010

Following is a tutorial on how to flash LG KS660 with LG GSMULTI 3.0. Let’s go. LG Phone Problem and Solution

In this tutorial you will see how to flash LG KS660 with new firmware.

1.) BACKUP
– First off all you should make a backup of your phone files (contacts, messages …) because after flashing, all the files saved on the phone will be erased. I recommend that you use LG PC SuiteII.
– Don’t forget to unplug your LG KS660.

2.)DOWNLOAD GSMULTI AND FIRMWARE
FIRMWARE KS660AT-00-V10g-CIS-JUN-02-2009

FLASHER LG – MultiGSM ver 3.0 + ks660.dll file

3.)INSTALL THE SOFTWARE AND DRIVERS – DRIVERS WORKS ONLY ON XP WINDOWS
(Don’t connect your LG KS660 on computer yet)
Downloaded files should be un-zipped (I unzipped them in one folder which i made it on desktop)
You got next files:
program
– SETUP_GSMULTI_V30

– KS660_090105.dll

firmware
– KS660AT-00-V10g-CIS-JUN-02-2009

3.1.) Install GSMULTI (SETUP_GSMULTI_V30). The icon will shows on your desktop otherwise the program install on C disk, folder GSMULTI
– start GSMULTI
– select: Settings/Configuration
– put .dll file and firmware file in and choose USB then click OK and close program

3.2.)Install DRIVERS (INFINEON and TI_NEPTUNE)
Drivers to be found in install folder of GSMMULTI program. My path is C:\GSMULTI\UsbDrivers
– First install INFINEON
– Second TI_NEPTUNE

4.) PREPARE AND CONNECT YOUR PHONE
– Now u take a phone (shut it down) and remove, BATTERY, SIM CARD and MEMORY CARD then
– connect it with your USB cable to computer (I suggest that u connect only in one USB port on computer)
– wait about one minute that computer recognize new device

5.) USBMap PROGRAM
– Run program USBMap_V01 (which can be found in C:\GSMULTI)
– Select INFINEON and then click MAPPING START
-WAIT (about one minute) that USBMAP will find USB port where is the phone connected
– When the port will be found click on (select it) and press SAVE&EXIT

6.)MAIN PART – FLASHING
– Run GSMULTI program (shourtcut is in your desktop)
– Check if settings/configuration are the same like we set it before (otherwise look step 3.1.)

– Now its everything ready to start flashing
– Check MODEL and SW VERSION and if that is correct just click START and wait until the program finished

– And voila, here we have a new firmware version.

LG Cell Phone – Related Posts

Comments

khalid salim on 8 December, 2010 at 2:33 pm #

if it has a security code can i flash it if i cant then how do u unlock a lg ks660 with security code?


Alex on 23 February, 2011 at 6:57 am #

Thanks man! It worked like a charm!
You didn’t mention that you have to load the 2 firmware files (sg and sg3 .bin) which is obvious, of course…


pawan on 25 October, 2011 at 10:52 am #

i done Flasing as per above shown process on my KS660 BUT its not complet, shows fail (317 sec).my original firmware was KS660AT-00-V10b.can any one help me plz.


pawan on 25 October, 2011 at 10:53 am #

i done Flasing as per above shown process on my KS660 BUT its not complet, shows fail (317 sec).my original firmware was KS660AT-00-V10b.can any one help me plz.my mail id is pawankt2003@yahoo.co.in


Dr. Ahmed El-Belbeisy on 13 January, 2012 at 10:50 am #

Kindly, help me about the following issue;
1. I did everything as it says but it looks like if it is not compatible with windows 7 ultimate 64bit, because the “Flash Utility Driver” doesn’t appear at my universal serial bus devices in device manager.
2. When I map the phone it doesn’t find it.
Kindly, inform me about what to do. Thanks in advance for your time and effort.


Imran on 23 August, 2012 at 9:39 am #

Hi,

I have similar problem, unable to map, waited almost 5 minutes and tried couple of times nil help.
Can anyone advise on this


Post a Comment
Name:
Email:
Website:
Comments: